Can you sand glazing compound

Using a paper towel or wash cloth, rub the rubbing alcohol into the putty. Glazing , which derives from the Middle English for ' glass ', is a part of a wall or window, made of glass. Glazing also describes the work done by a professional "glazier". Toughened and laminated glass can be glazed by bolting panes directly to a metal framework by bolts passing through drilled holes.

How do you smooth glazing putty? Category: home and garden home improvement. Old window panes: Smooth the compound. Is there an alternative to putty for Windows? Can I use caulk instead of glazing? How do I use old putty windows? How long does window putty take to dry? Can you paint over glazing putty? How thick can you apply glazing putty? Can you put glazing putty over paint? What is glaze putty used for?

Can you sand glazing putty? What color is Bondo glazing and spot putty? Product Details. What is the best glazing putty? Bondo over time absorbs water causing rust to form underneath. It can also shrink over time causing paint to bubble or peel off. If used.. Many times panes of glass in single pane, double hung wood windows have be repaired using caulk instead of the glazing compound traditionally used. Nobody uses caulk for a good reason,it does not stick to dissimilar or porous wood surfaces very well.

Yes it can be wet sanded,tell your friend to research 2pak paint before talking poo :p. Plus every wetsanding you see done on this site is 2k. Is there a spot putty that is more flexible that will adhere to semi-rigid plastics? Pinholes can sometimes be caused by using too much hardner. Dryseal is a modern elastic glazing putty sealant which is recommended for use in sash window renovation as a durable alternative to linseed oil putty.

An excellent advantage is that Dryseal is moisture and UV resistant, great for sash window repair and especially good for south facing windows. If you are using a two-part catalyzed glazing putty , this should not take longer than an hour.

If you are using one -part, it can take up to a day. Using a fine grit sandpaper or up sand the area once again, taking care to keep the sandpaper level and pressure applied equally. Generally, in a matter if a few minutes it will start to harden and get rubbery. At that point, you can carve it up with a utility knife, a hand planer or a bondo rasp.

Just make sure you leave enough to do a final sanding , usually within 10 to 15 minutes you can start sanding it. Under most circumstances you will not need to DA sand over your work after wet sanding because wet sanding creates much finer scratches. Everything must be scuffed or sanded in some way. I use a combination of my hands, a glazier's tool, putty knife, razor blade, and then the tips of my fingers. I'll do a little tutorial on glazing later this week so you can see just how easy though time consuming it can be.

Waiting for the tutorial impatiently. I have a broken pane on the back door - yes the ugly, nasty back door that also has the rotten spring bronze on it. The weatherstripping and window replacement need to be done before it gets a whole lot colder Sarco Glazing.

You pass the test. When I saw glazing, I thought for sure, oh no this is where we part ways. But then there was that big fat yellow can of Sarco. Well done. The only thing better would be if you had some linseed oil and whiting and mixed your own glazing.

I'm guessing you've been to this forum, if not, here's a 10 page forum analysis of different glazing putties and techniques. Get your geek on: www. This is excellent information, thanks for posting! Hah, thanks Brendan! I always strive to do things the right way. If I'm not doing the right thing or at least attempting it it's probably because I just don't know better. This is my first time using the Sarco products, but I've been waiting to use it for a while, just needed a project.

I used to use DAP, but I think they changed the formula and it is impossible to work with now. Besides, I've just never liked it for an external window, and that is what these essentially are. I've actually not been to that forum, so thinks for the link. I just looked through all of the pages, tons of great information. What epoxy do you like to use for wood filler?

Since you've not signed in yet, you will need to fill in your name and email below. If you have a Facebook account, save yourself a step and use Connect to login. Email Address. Status Pending Approved Removed Declined. Comment You can use Markdown syntax in your comment. And you can also use lots of Emoji!

Click on any of the items below to insert it into the comment area. Notify Me When a comment is left for this post When a reply is made to my comment No notifications. Submit Your Comment Cancel. Search Search Blog. First time here?

Meet Us! Login Follow Advertising. Be sure that your glazing compound, rags and putty knife are available. Arrange the sanding material and spray-on primer in an organized fashion around your work area. Spread a drop cloth below your work area, particularly if you are working outside; all of the materials you are using are toxic to the environment and you should take care to protect the area from these toxins.

Prepare the surface you will be working on. Using grit sandpaper and a hand sander block or, if you doubt the strength of your arms and the area you are sanding is particularly rough, an electric hand held sander completely smooth the area. Use a cloth to wipe away the paint and metal dust. Rinse off the area with water and dry thoroughly. Spray on two coats of primer. Allow primer to dry.